PFC-Pentax Fans Club

 取回密碼
 註冊
直達第 跳轉
返回清單 發表主題
檢視: 1295|回覆: 14

k10原廠的Firmware Update? [複製連結]

中級會員

註冊時間
2006-11-1
主題
14
發表
124
精華
0
威望
177
積分
152
最後登入
2012-10-30
發表於 2007-1-23 09:00:22 |顯示全部樓層 | 字體大小
不是謠傳今天會出現?好像沒有ㄟ??
那上次的地下版本是否還有問題呢?或是原廠仍會增加新的修正?
有哪個先進了解"內幕"呢?;)

中級會員

註冊時間
2006-11-1
主題
2
發表
57
精華
0
威望
70
積分
61
最後登入
2014-11-7
發表於 2007-1-23 09:09:00 |顯示全部樓層 | 字體大小
美國的已經release了
http://www.pentaximaging.com/cus ... ware?firmId=8793673

K10D



PENTAX K10D FIRMWARE UPDATE VERSION 1.10



VERSION HISTORY



Version 1.10 (CLICK HERE for a PDF containing more details on these changes):

Using the camera's built-in flash, you can now wirelessly control external Pentax flashes. Previously, you needed an accessory flash mounted in your camera's hot shoe, but now the built-in flash can act as a control flash.
In autofocus select mode, you can program the AF button to instantly return to the center autofocus point.
In Tv or Av mode, you can now program the second e-dial to adjust your ISO setting.
In any exposure mode except Sv and TAv, you can change your ISO setting with the front e-dial while pressing the OK button. The camera will display your ISO in the viewfinder and on the top LCD panel as you adjust your setting.
In TAv mode, you can program the green button to return to the camera's program line. Previously this functionality was only available in M mode.
You now have additional options for programming your e-dials in P mode.
Pressing the green button while adjusting flash exposure compensation will now return you to the default value.
Corrected an issue in some rare cases where a long exposure might produce a vertical stripe.
Corrected an issue where the battery charge indicator would sometimes show empty in bulb exposure mode.
PREPARATION

You will need a blank, formatted memory card with a capacity of 16MB or higher.
You will need your camera's USB cable, or a memory card reader.
Make sure your batteries are fresh, or that you are using an optional AC adapter to prevent power interruptions during the update process.
Make sure your camera currently has firmware version 1.00. You can check your current firmware version by turning the camera on while holding down the MENU button.
FIRMWARE UPDATE INSTRUCTIONS - WINDOWS

Click the Windows link below to download the self-extracting firmware archive file (k10e110w.exe). Click SAVE to save the download file to your computer's hard drive. Saving it to your desktop, for example, will make it easy to find after the download is complete. Please note: this download file is not the firmware update file itself, but a compressed archive that must be expanded in the following step.
Next, double click the download file to expand it. Once expanded, you will see a readme text file (README.TXT) and the firmware update file itself (FWDC162B.BIN). The readme file contains instructions similar to what you are reading on this page.
You must now copy the firmware update file (FWDC162B.BIN) to your camera's memory card. When you connect the camera directly to your computer (or if you use a card reader), the memory card appears as a removable disk drive in the My Computer window. Make sure you are using a blank/formatted memory card, then drag & drop (or copy & paste) the firmware update file (FWDC162B.BIN) from the desktop to your removable disk window, which is the camera's memory card. Please note: You must put the firmware update file (FWDC162B.BIN) directly onto the removable disk; it cannot be in any sub-folders. It must be on the top (or root) level of the removable disk.
Now that you have copied the firmware update file (FWDC162B.BIN) to your camera's memory card, you are ready to install it. Make sure your camera is turned off and disconnected from the computer. Make sure that the memory card containing the firmware update file is inserted into your camera. Also, make sure you that you have adequate power in your camera. We recommend you use a Pentax AC adapter to perform the firmware update, but if you do not have a Pentax AC adapter, make certain that your batteries have a full charge.
To begin the update, turn your camera on while holding down the MENU button. If you have followed the above instructions precisely, the camera will begin to load the new firmware. You will see the message "NOW LOADING" then the camera will display the firmware update menu.
Select "YES" using your camera's 4-way controller (the default is "NO") then press your camera's OK button.
The camera will now update its firmware. This may take a couple of minutes, so be careful to not interrupt the process.
When the update is complete, you will see "COMPLETE" on your camera's LCD screen. Turn the camera off and remove the memory card.
With the memory card removed from the camera, check your new firmware version by turning the camera back on while holding down the MENU button. Before you begin to take pictures again, be sure to format your memory card to erase the firmware update file.
FIRMWARE UPDATE INSTRUCTIONS - MACINTOSH

Mac users can follow this same process after clicking on the Macintosh download link below.

Download and save the Macintosh download file.
Decompress it with your Stuffit expander program.
Connect the camera to the computer.
Copy the firmware file (FWDC162B.BIN) to your camera's memory card, then disconnect the camera from the computer.
Proceed with the installation of the firmware as outlined above.
DOWNLOAD

You may wish to print this page to use as a reference when updating your camera.

DOWNLOAD WINDOWS FILE (1.55 MB)
DOWNLOAD MACINTOSH FILE (1.97 MB)

中級會員

註冊時間
2006-11-1
主題
14
發表
124
精華
0
威望
177
積分
152
最後登入
2012-10-30
發表於 2007-1-23 09:18:29 |顯示全部樓層 | 字體大小
謝謝!!
跟地下流出版的一模一樣嗎?
奇怪的是...為何日本的還沒?

北區客服

註冊時間
2005-6-6
主題
117
發表
2317
精華
1
威望
6798
積分
2556
最後登入
2016-10-27
發表於 2007-1-23 09:23:56 |顯示全部樓層 | 字體大小
美國原廠網站也算原廠囉
這樣就可以安心更新了
冷冷的

中級會員

註冊時間
2006-12-25
主題
1
發表
26
精華
0
威望
54
積分
28
最後登入
2009-6-8
發表於 2007-1-23 09:42:31 |顯示全部樓層 | 字體大小
firmware有分語系嗎??
搞錯就糗了

丸子好好笑

註冊時間
2005-10-5
主題
6
發表
115
精華
0
威望
289
積分
127
最後登入
2013-2-27
發表於 2007-1-23 09:48:37 |顯示全部樓層 | 字體大小
Post by blesshammer;244066
firmware有分語系嗎??
搞錯就糗了


不用害怕

全球 pentax 韌體都一樣

歐版 的也有中文 美版的當然也有

中級會員

註冊時間
2006-11-1
主題
14
發表
124
精華
0
威望
177
積分
152
最後登入
2012-10-30
發表於 2007-1-23 09:48:59 |顯示全部樓層 | 字體大小
這次的更新似乎並沒有針對"jpg 或 過曝 "做適當的修改...

Sr. la disai

註冊時間
2006-1-25
主題
20
發表
1961
精華
0
威望
4223
積分
2001
最後登入
2012-1-31
發表於 2007-1-23 09:54:18 |顯示全部樓層 | 字體大小
Post by lyykiki;244081
這次的更新似乎並沒有針對"jpg 或 過曝 "做適當的修改...


根據以往iSTDs的韌體修改經驗,
關於JPEG的修改Pentax只會私下做,不會公開告訴你的~
有老美說高ISO表現有好一點,過曝還是有發生。

希望有update的同好給一些測試喔!
(攻擊)(攻擊)(攻擊)

中級會員

註冊時間
2006-11-1
主題
2
發表
57
精華
0
威望
70
積分
61
最後登入
2014-11-7
發表於 2007-1-23 10:01:07 |顯示全部樓層 | 字體大小
日本的也有了
http://www.pentax.co.jp/japan/su ... digital/k10d_s.html

比對過,日本的跟美國的是一樣的,不會有搞錯的問題

日本網站有提到修改項目:
1. バルブ(B)の長時間露光(約5分以上)を行った際に、まれに画像にムラが出る症状に対応しました。
2. 低温での撮影環境下でバルブ(B)の長時間露光を行うと、条件によっては電池残量なしの表示がすぐに出てしまう症状に対応しました。

因為我也不懂日文,所以請大家用翻譯軟體翻吧

剛入門的新手

註冊時間
2005-1-21
主題
66
發表
1488
精華
1
威望
2947
積分
1625
最後登入
2016-12-2
發表於 2007-1-23 10:03:57 |顯示全部樓層 | 字體大小
Post by lyykiki;244081
這次的更新似乎並沒有針對"jpg 或 過曝 "做適當的修改...

個人覺得與其說是過曝,不如說是測光機制與之前的系統有所不同...而jpg檔在實拍上也沒有感覺比raw檔還軟啊...

有興趣請參考小弟的實拍心得:http://www.pentaxfans.net/showthread.php?p=242476#post242476
直達第 跳轉
返回清單 發表主題
你需要登入後才可以回覆 登入 | 註冊 |

招商合作|Archiver|PFC-Pentax Fans Club |網站地圖  

GMT+8, 2016-12-5 08:41 , Processed in 0.024836 second(s), 4 queries , Gzip On, Eaccelerator On.

Powered by PFC

© 2004-2016 Pentax Fans Club

回頂部